Ross Kitson Popular Books

Ross Kitson Biography & Facts

A steam diesel hybrid locomotive is a railway locomotive with a piston engine which could run on either steam from a boiler or diesel fuel. Examples were built in the United Kingdom, Soviet Union and Italy but the relatively high cost of fuel oil, or failure to resolve problems caused by technical complexity, meant that the designs were not pursued. Kitson-Still system In 1926 Kitson and Company, Leeds, built an experimental example for the London and North Eastern Railway, using as their model the Still engine already in use for stationary and marine applications. It was on trial until 1934, but then scrapped. It was designed because a steam engine offered a high starting torque—a tractive force of 25,450 lbf (113.2 kN) was available—while a diesel engine offered a high fuel efficiency and it was considered desirable to combine both benefits in one machine. Construction In outline the machine resembled a conventional 2-6-2T steam locomotive, but it had four pairs of horizontally opposed cylinders (13½ inch bore × 15½ inch stroke—343 × 394 mm) mounted longitudinally above the frame and driving a crankshaft placed between them, with the further drivetrain by gears. The cylinders were made double-ended, with the rod end of each cylinder for steam and the closed end fitted with a diesel injector. (Some drawings, published in contemporary magazines, show only two pairs of cylinders and it seems that this was one of the design features that was changed during development.) The boiler, with a diameter of only 51 inches (130 cm) and a small internal firebox, was mounted above. The "regenerator", capturing heat from the exhaust, was integral with the boiler and had 38 tubes totalling a heating area of 508 sq ft (47 m2). The driving position was in the usual place behind the boiler, and tanks—400 imperial gallons (1,800 litres) for fuel and 1,000 imperial gallons (4,500 litres) for water—were mounted on the frame at the rear, one above the other. Operation The sequence of operation began with heating the boiler in the normal way, but using fuel oil instead of coal. The start from rest was made with steam power, but at about five mph (8 km/h) the diesel injectors were started and the steam turned off. The waste heat from the cylinder jackets and diesel exhaust then maintained the boiler in steam for auxiliary functions (brakes and whistle) and in readiness to supplement the diesel power if required, or for the next start. The temperature of the water jacket, maintained at considerably above boiling point, assisted the compression ignition of the diesel fuel and only a relatively low compression ratio was required. Because steam power provided the torque required for starting, no form of variable transmission was necessary and a permanent reduction geartrain of ratio 1·878 to 1 was fitted.Overall power output (800 bhp under diesel, 1,000 bhp when supplemented with steam) did not compare well with conventional steam locomotives, although the performance on gradients was good because of the gearing. During the trials it was used successfully with coal trains and it proved very efficient in terms of fuel used, because the waste heat from the diesel power was recovered. However its running costs depended on the price differential between coal and oil and this was not favourable. When Kitson & Co. failed in 1934 the LNER handed the machine back to the company's receivers and it was dismantled. Cristiani compressed steam system The Italian Cristiani Compressed Steam System used the process of mechanical vapour recompression. A diesel engine compressed steam which was then fed to conventional steam engine cylinders. The exhaust steam was re-compressed and used again. There must have been a small boiler to generate the initial charge of steam but this is not shown in the diagram.The steam was used mainly as a transmission system but the locomotive does count as a hybrid because some steam storage was provided. A possible advantage of the system was that it enabled existing steam locomotives to be converted to diesel operation but this did not come to fruition. Patents for the system were held by Severino Cristiani and Secondo Sacerdole in Italy and it was promoted in England by Captain William Peter Durtnall. A trial was made in England, using two "Paragon" marine petrol engines, under the name "Paragon-Cristiani". The equipment was mounted on a 0-6-0 chassis (works number 3513/1923) built by Hawthorn Leslie and Company. It was not a success and the chassis was converted to a conventional 0-6-0ST named "Stagshaw" which is preserved on the Tanfield Railway. Other trials Soviet Union The Soviet Union built three large experimental locomotives between 1939 and 1946.The first prototype, numbered 8000, a 2-8-2 from the Vorishilovgrad works, had two pairs of outside double-acting opposing pistons; when diesel power was initiated, at about 20 km/h (12 mph), diesel fuel was injected into the centre portion between the pistons which thus became the compression-ignition chamber, while the outer ends of the cylinders continued to receive steam in the normal way. Although the unit remained in passenger service, intermittently, until 1946, when it was tested again. It was put into storage in 1948. It was not considered a success as its 25-tonne axle load was too high, it rode hard on the tracks and was prone to cracking cylinders.TP1-1, the second prototype (illustrated right), under the name of Сталинец (Stalinets), was a cab-forward condensing 2-10-2 from the Kolomna works, used gas produced from an anthracite coal plant in the tender to fuel its spark-ignition internal combustion cylinders, along with anthracite pulverised in the gasification plant to heat the boiler. There were a total of eight pistons in four cylinders in an opposed-piston configuration; two steam cylinders and two coal gas cylinders. It was reported to have only functioned properly at speeds of 25–30 km/h and below as travelling faster for about 10–15 minutes would cause the gas mixture to combust prematurely when entering the combustion chamber. Issues were reportedly sorted out by 1941 but the project was abandoned during Operation Barbarossa and the outbreak of WW2 on Soviet territory.Number 8001, the third experiment, also named Сталинец, was a unit developed from the previous Voroshilovgrad design in 1946. It was also a 2-10-2 configuration and had the centre space in the cylinders, between the opposed pistons, intended to combine compression ignition and steam expansive working in the same chamber. It was reportedly almost a complete disaster and placed in storage in 1948. Switzerland In 1925, Jakob Buchli of Switzerland obtained US patent 1559548 for a combined steam and internal-combustion engined locomotive. This differed from the Kitson-Still system in that there was no waste heat recovery and the steam and internal combustion engines had separate cylinders (vertically mounted in the tender), but both.... Discover the Ross Kitson popular books. Find the top 100 most popular Ross Kitson books.

Best Seller Ross Kitson Books of 2024

  • The Infinity Bridge synopsis, comments

    The Infinity Bridge

    Ross Kitson

    Sam: likes loud music, wears black eyeliner... and sees monsters.Nick: wears Che Guevara knitwear, big specs, loves scifi... and designs computer viruses.Annie: dresses like a Sund...